D4d.3 & D8d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM
PACO SUBMERSIBLE NON-CLOG PUMPS, TYPE (NSC) D4d.3 AND PACO SUBMERSIBLE SUMP PUMPS, TYPE (SM) D8d.3
SM
NSC
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM
TABLE OF CONTENTS I.
INSTALLATION…………………………………………………………………… 3
II.
OPERATION……………………………………………………………….………. 3
III. DISSASEMBLY OF PUMPS……………………………………………………… 4 IV. TROUBLE SHOOTING………………………………………………………………………… 4 V. ORDERING PARTS……………………………………………………………………………. 4
2
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM
1. INSTALLATION Read these instructions thoroughly before installing and operating your PACO Type SM/NCS Submersible Pump. Successful operation depends on careful attention to the procedures described in this manual. Keep this instruction manual handy for future use. a. Pump Identification: All PACO Pumps are identified by Catalog and Serial Numbers. These numbers are stamped on the pump nameplate (Fig. 1) affixed to each pump volute casing, and should be referred to in all correspondence with the Company.
FIG. 1 PUMP NAMEPLATE
b. Pump is designed to sit on a concrete or metal pump bottom. It should not sit on a dirt bottom. c. Pipe discharge to sewer, using a check valve to prevent back-flow. On a duplex installation, use a check valve in each pump discharge line. Locate check valve(s) as far away from pump bottom as possible, to avoid possibility of air binding. Be certain that weight of discharge piping is supported so it does not put a strain on pump casting. End of pipe entering pump discharge flange is to be unthreaded, as special pump flange makes an O-ring seal around it. d. Fasten pump chain to sump cover, to provide means of lifting pump when needed. If it becomes necessary to
replace chain, do not use a smaller size than chain supplied with pump. e. Install and adjust liquid level control in accordance with the liquid level control instruction sheet. f. Read motor instruction manual and make electrical connections. A third leg overload protection in the starter is recommended as is moisture-sensing controls. g. Before starting pump, clean sump of debris, which might clog the pump, such as rags, paper, canvas gloves, blocks of wood. h. If motor is three phase, check its direction of rotation by either of the following methods: (1) With pump hanging free of the bottom, and with discharge not connected (but with a piece of burlap wired over it to prevent water discharging too far) turn motor on and then off immediately. As the correct rotation of pump is right hand (clockwise), the “kickback” should be left hand (CCW), looking down on the motor from above it. If it kicks back in wrong direction, interchange any two leads at bottom of entrance switch (after turning off switch first) and try again. (2) Alternate method: Fill sump. Turn pump on and operate it. Note the amount of water pumped out of sump and the time it took. Interchange any two leads at bottom of entrance switch (after turning switch off, first, and marking the leads): fill sump again and try pump again for the same time. The connection which pumps water out at the faster rate is the correct connection, as pump will pump at a much faster rate when running correct rotation than when running backward.
3
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM
2. OPERATION a. This motor does not require lubrication attention. Never disassemble the motor.
b. Water level must be above the motor at all times while operating to provide necessary cooling. While it is permissible to operate pump for a few minutes, manually, to pump the water down as low as possible to clean out the sump or to remove pump, the motor must not operate without water surrounding it completely for more than 15 minutes. Set the level control carefully so that pump shuts off before water starts to uncover top of motor in normal operation. c. Check voltage while pump is operating. Voltage must not vary more than 10% from rated voltage stamped on motor nameplate. d. Recheck direction of rotation of motor at any time any alterations are made in system wiring. e. Do not lift unit by the motor cable, or conduit. Lifting lugs are provided on the unit; use them.
3. TO DISASSEMBLE THE PUMP a. Remove pump from sump. If necessary to disconnect wiring, mark leads carefully so they will be reconnected in same manner. b. To replace impeller, remove volute and remove impeller cap screw and washer. Use wheel or gear pullers to remove impeller or warm impeller slightly with a torch to expand it, and, with two large screwdrivers or small pry bars, one on each side between impeller and backplate, pry carefully and evenly to force impeller off of shaft. BE VERY CAREFUL TO PRY EVENLY SO AS NOT TO BEND SHAFT. c. Reassemble in reverse order. Under no circumstances should impeller be driven
Disassembly of motor outside of an authorized service shop of the motor manufacturer voids the motor warranty. on by pounding, as this would damage the seal. Use impeller cap screw to gradually pull impeller onto shaft.
4. CHECKING FOR TROUBLE a. If pump will not deliver any water, or delivers less water than normal: (1) See that pump is running right hand (CW), looking downward. (2) Check impeller to see that it is not plugged with debris. (3) Check motor nameplate to see that it is correct speed for pump. (4) Check to see that suction screen is not clogged or buried in muck or debris so as to cut down amount of water reaching pump. (5) Check pump operating discharge head. Compare to pump selection head. b. If motor overheats, blows fuses, or magnetic switch trips off, check to see that: (1) Voltage is same as stamped on motor nameplate – not any lower. (Power company can check the voltage for you. Be sure to check at time when voltage is usually low, such as evening.) (2) Motor is not faster speed than correct for pump. (3) Head is not lower than unit is selected for. Centrifugal pumps will overload at heads lower than they are selected for, due to pumping increased capacity at lower heads.
4
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM (4) If liquid is heavier than water, motor size must be selected to handle this heavier specific gravity. (5) If liquid is more viscous than water, motor size must be selected to handle this greater viscosity. (6) Shaft is not bent. (7) Impeller is not rubbing on bottom of pump. (8) Check heater and fuse selection.
5. ORDERING PARTS • PACO PUMPS has over 90 years of experience in the design, manufacture, and application of centrifugal pumps and pumping systems. PACO’s commitment to state-of-the art pump design and quality manufacturing assures maximum user benefits with optimum equipment life at lower cost. • PACO’s commitment to their customers continues through an extensive service organization. Highly trained technicians can assist customers with initial startup,
troubleshooting, repair, and system analysis. PACO maintains an extensive stock of replacement parts and part kits for out most popular model pumps. Shipment of these parts is normally made within three days after receipt of an order. On larger pumps, where it is impractical for our factory to inventory low usage parts, replacement parts are normally manufactured and shipped within 15 working days of receipt of an order. In order to reduce pump repair time and shorten inconvenient pump service interruptions, it is suggested that the pump user stock spare parts. For suggested spare parts see Replacement Parts Guide D8b.2, attached, and contact your local PACO Sales Representative (see back cover for the number of your nearest PACO sales office). Since spare parts requirements and quantities vary for specific pump constructions, allow your PACO Representative to help in defining your spare part requirements. To ensure that the proper replacement parts are ordered for your particular pump model, when you call: •
Identify all pertinent data from the pump nameplate (see Pump Identification). This should always include the pump Catalog or Model Number, and the pump Serial Number.
•
For replacement impellers, also include from the nameplate the operating conditions (GPM and TDH) and the impeller diameter.
•
Identify all parts by item number and description as indicated by the appropriate assembly drawing in this manual, for your particular pump model.
5
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM
1P
–
VOLUTE, LOWER
1N –
VOLUTE, UPPER
3A
IMPELLER
–
5B
–
SPACER
8A
–
SCREW, IMPELLER
10A –
WASHER, IMPELLER
12A –
KEY, IMPELLER
17N –
GASKET, DISCHARGE
30B –
FLANGE, DISCHARGE
44B –
SCREEN
65L – MOTOR
FIG. 2
SUBMERSIBLE SUMP PUMP TYPE “SM”
FIG. 3 SUBMERSIBLE NON-CLOG PUMP TYPE “NSC”
6
PACO SUBMERSIBLE NON-CLOG PUMPS, TYPE (NSC) D4d.3 AND PACO SUBMERSIBLE SUMP PUMPS, TYPE (SM) D8d.3
SM
NSC
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM
TABLE OF CONTENTS I.
INSTALLATION…………………………………………………………………… 3
II.
OPERATION……………………………………………………………….………. 3
III. DISSASEMBLY OF PUMPS……………………………………………………… 4 IV. TROUBLE SHOOTING………………………………………………………………………… 4 V. ORDERING PARTS……………………………………………………………………………. 4
2
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM
1. INSTALLATION Read these instructions thoroughly before installing and operating your PACO Type SM/NCS Submersible Pump. Successful operation depends on careful attention to the procedures described in this manual. Keep this instruction manual handy for future use. a. Pump Identification: All PACO Pumps are identified by Catalog and Serial Numbers. These numbers are stamped on the pump nameplate (Fig. 1) affixed to each pump volute casing, and should be referred to in all correspondence with the Company.
FIG. 1 PUMP NAMEPLATE
b. Pump is designed to sit on a concrete or metal pump bottom. It should not sit on a dirt bottom. c. Pipe discharge to sewer, using a check valve to prevent back-flow. On a duplex installation, use a check valve in each pump discharge line. Locate check valve(s) as far away from pump bottom as possible, to avoid possibility of air binding. Be certain that weight of discharge piping is supported so it does not put a strain on pump casting. End of pipe entering pump discharge flange is to be unthreaded, as special pump flange makes an O-ring seal around it. d. Fasten pump chain to sump cover, to provide means of lifting pump when needed. If it becomes necessary to
replace chain, do not use a smaller size than chain supplied with pump. e. Install and adjust liquid level control in accordance with the liquid level control instruction sheet. f. Read motor instruction manual and make electrical connections. A third leg overload protection in the starter is recommended as is moisture-sensing controls. g. Before starting pump, clean sump of debris, which might clog the pump, such as rags, paper, canvas gloves, blocks of wood. h. If motor is three phase, check its direction of rotation by either of the following methods: (1) With pump hanging free of the bottom, and with discharge not connected (but with a piece of burlap wired over it to prevent water discharging too far) turn motor on and then off immediately. As the correct rotation of pump is right hand (clockwise), the “kickback” should be left hand (CCW), looking down on the motor from above it. If it kicks back in wrong direction, interchange any two leads at bottom of entrance switch (after turning off switch first) and try again. (2) Alternate method: Fill sump. Turn pump on and operate it. Note the amount of water pumped out of sump and the time it took. Interchange any two leads at bottom of entrance switch (after turning switch off, first, and marking the leads): fill sump again and try pump again for the same time. The connection which pumps water out at the faster rate is the correct connection, as pump will pump at a much faster rate when running correct rotation than when running backward.
3
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM
2. OPERATION a. This motor does not require lubrication attention. Never disassemble the motor.
b. Water level must be above the motor at all times while operating to provide necessary cooling. While it is permissible to operate pump for a few minutes, manually, to pump the water down as low as possible to clean out the sump or to remove pump, the motor must not operate without water surrounding it completely for more than 15 minutes. Set the level control carefully so that pump shuts off before water starts to uncover top of motor in normal operation. c. Check voltage while pump is operating. Voltage must not vary more than 10% from rated voltage stamped on motor nameplate. d. Recheck direction of rotation of motor at any time any alterations are made in system wiring. e. Do not lift unit by the motor cable, or conduit. Lifting lugs are provided on the unit; use them.
3. TO DISASSEMBLE THE PUMP a. Remove pump from sump. If necessary to disconnect wiring, mark leads carefully so they will be reconnected in same manner. b. To replace impeller, remove volute and remove impeller cap screw and washer. Use wheel or gear pullers to remove impeller or warm impeller slightly with a torch to expand it, and, with two large screwdrivers or small pry bars, one on each side between impeller and backplate, pry carefully and evenly to force impeller off of shaft. BE VERY CAREFUL TO PRY EVENLY SO AS NOT TO BEND SHAFT. c. Reassemble in reverse order. Under no circumstances should impeller be driven
Disassembly of motor outside of an authorized service shop of the motor manufacturer voids the motor warranty. on by pounding, as this would damage the seal. Use impeller cap screw to gradually pull impeller onto shaft.
4. CHECKING FOR TROUBLE a. If pump will not deliver any water, or delivers less water than normal: (1) See that pump is running right hand (CW), looking downward. (2) Check impeller to see that it is not plugged with debris. (3) Check motor nameplate to see that it is correct speed for pump. (4) Check to see that suction screen is not clogged or buried in muck or debris so as to cut down amount of water reaching pump. (5) Check pump operating discharge head. Compare to pump selection head. b. If motor overheats, blows fuses, or magnetic switch trips off, check to see that: (1) Voltage is same as stamped on motor nameplate – not any lower. (Power company can check the voltage for you. Be sure to check at time when voltage is usually low, such as evening.) (2) Motor is not faster speed than correct for pump. (3) Head is not lower than unit is selected for. Centrifugal pumps will overload at heads lower than they are selected for, due to pumping increased capacity at lower heads.
4
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM (4) If liquid is heavier than water, motor size must be selected to handle this heavier specific gravity. (5) If liquid is more viscous than water, motor size must be selected to handle this greater viscosity. (6) Shaft is not bent. (7) Impeller is not rubbing on bottom of pump. (8) Check heater and fuse selection.
5. ORDERING PARTS • PACO PUMPS has over 90 years of experience in the design, manufacture, and application of centrifugal pumps and pumping systems. PACO’s commitment to state-of-the art pump design and quality manufacturing assures maximum user benefits with optimum equipment life at lower cost. • PACO’s commitment to their customers continues through an extensive service organization. Highly trained technicians can assist customers with initial startup,
troubleshooting, repair, and system analysis. PACO maintains an extensive stock of replacement parts and part kits for out most popular model pumps. Shipment of these parts is normally made within three days after receipt of an order. On larger pumps, where it is impractical for our factory to inventory low usage parts, replacement parts are normally manufactured and shipped within 15 working days of receipt of an order. In order to reduce pump repair time and shorten inconvenient pump service interruptions, it is suggested that the pump user stock spare parts. For suggested spare parts see Replacement Parts Guide D8b.2, attached, and contact your local PACO Sales Representative (see back cover for the number of your nearest PACO sales office). Since spare parts requirements and quantities vary for specific pump constructions, allow your PACO Representative to help in defining your spare part requirements. To ensure that the proper replacement parts are ordered for your particular pump model, when you call: •
Identify all pertinent data from the pump nameplate (see Pump Identification). This should always include the pump Catalog or Model Number, and the pump Serial Number.
•
For replacement impellers, also include from the nameplate the operating conditions (GPM and TDH) and the impeller diameter.
•
Identify all parts by item number and description as indicated by the appropriate assembly drawing in this manual, for your particular pump model.
5
D4d.3 8/06 Supercedes All INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS TYPE NSC & TYPE SM
1P
–
VOLUTE, LOWER
1N –
VOLUTE, UPPER
3A
IMPELLER
–
5B
–
SPACER
8A
–
SCREW, IMPELLER
10A –
WASHER, IMPELLER
12A –
KEY, IMPELLER
17N –
GASKET, DISCHARGE
30B –
FLANGE, DISCHARGE
44B –
SCREEN
65L – MOTOR
FIG. 2
SUBMERSIBLE SUMP PUMP TYPE “SM”
FIG. 3 SUBMERSIBLE NON-CLOG PUMP TYPE “NSC”
6
B1b.2 07/07 Supersedes 9/05
PACO PUMPS
SPLIT CASE PUMPS REPLACEMENT PARTS GUIDE TYPES KP & KPV
®
CAT#: STOCK#:
WWW.PACOPUMPS.COM
SER#: IMP
GPM:
DIA: TDH: BROOKSHIRE, TEXAS
'
PACO Split Case Kits are arranged so that you can replace virtually any component with minimum of effort. Here are some guidelines and suggestions: GENERAL NOTES: The pump nameplate contains all data required for the selection and ordering of the proper replacement parts kit. The PUMP MODEL and SERIAL NUMBER should be referenced whenever any replacement parts kit is ordered, while the PUMP CONDITIONS (GPM & TDH) and IMPELLER TRIM (IMP DIA) are REQUIRED data for the ordering of replacement impellers. To replace a mechanical seal. Select the correct Seal Kit which will maximize seal life and eliminate future down time. Shaft sleeve inspection is suggested, and replacement made as indicated. (Note that a PACO Seal kit will already contain a complete Gasket Kit and Bearing Kit)
To replace impeller. An Impeller Kit is required; a Wear Ring Kit is highly recommended, and a Seal or Packing Kit will provide all other normally replaced components.
To replace the packing A packing kit is needed. Shaft sleeve inspection is recommended. If packing glands are damaged, they may be replaced by ordering the proper Packing Gland kit. (Note that PACO Packing Kits will already contain a complete Gasket Kit and Bearing Kit).
To replace the shaft. The correct shaft should be selected. Shaft replacement is most often accompanied by replacement of the seal or packing and sleeves.
To replace the shaft sleeves. You will need a Shaft sleeve Kit. A Seal or Packing Kit will provide other normally needed parts.
To inspect the pump internals. Since gaskets are often damaged, a Gasket Kit is recommended.
To replace bearings. A Bearing Kit is required and a Gasket Kt is recommended. Bearing Kits and Gasket Kits are included in Seal/Packing Kits.
To overhaul the pump. (Replace Rotating Assembly). You will need an Impeller Kit, a Wear Ring Kit, a Shaft Sleeve Kit, a Seal or Packing Kit, and a shaft.
To replace wear rings. A Wear Ring kit is required. A Seal/Packing Kit will provide all other normally replaced components.
To replace lost or damaged hardware. Hardware Kits are available for 175 PSI units. (For 250 PSI refer to factory).
NOTE: Seal/Packing Kits are always recommended as spare parts
B1b.2 Page 1
B1b.2 07/07 Supersedes 9/05
REPLACEMENT PARTS GUIDE SPLIT CASE PUMPS Model
2095-1/2
Constr. Code
Mechanical Seal Kit To 200 PSI Working Pressure to 212psi Buna N Buna N Viton Viton Buna N Carbon Carbon Carbon Carbon Carbon Ceramic Ni Resist Ni Resist Tung Crbd Ceramic 1XXXXX 7XXXXX 6XXXXX 2XXXXX AXXXXX K0300-1 K0300-7 K0300-6 K0300-2 K0300-11 N/A N/A N/A N/A N/A K0300-1 K0300-7 K0300-6 K0300-2 K0300-11 N/A N/A N/A N/A N/A K0300-1 K0300-7 K0300-6 K0300-2 K0300-11 N/A N/A N/A N/A N/A K0414-1 K0414-7 K0414-6 K0414-2 K0414-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0416-1 K0416-7 K0416-6 K0416-2 K0416-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0418-1 K0418-7 K0418-6 K0418-2 K0418-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0306-1 K0306-7 K0306-6 K0306-2 K0306-11 K0306-1 K0306-7 K0306-6 K0306-2 K0306-11 K0307-1 K0307-7 K0307-6 K0307-2 K0307-11 K0307-1 K0307-7 K0307-6 K0307-2 K0307-11 K0308-1 K0308-7 K0308-6 K0308-2 K0308-11 K0308-1 K0308-7 K0308-6 K0308-2 K0308-11 K0309-1 K0309-7 K0309-6 K0309-2 K0309-11 K0309-1 K0309-7 K0309-6 K0309-2 K0309-11 K0334-1 K0334-7 K0334-6 K0334-2 K0334-11 K0309-1 K0309-7 K0309-6 K0309-2 K0309-11 K0334-1 K0334-7 K0334-6 K0334-2 K0334-11 K0309-1 K0309-7 K0309-6 K0309-2 K0309-11 K0458-1 K0458-7 K0458-6 K0458-2 K0458-A K0458-1 K0458-7 K0458-6 K0458-2 K0458-A K0458-1 K0458-7 K0458-6 K0458-2 K0458-A K0311-1 K0311-7 K0311-6 K0311-2 K0311-11 K0310-1 K0310-7 K0310-6 K0310-2 K0310-11 K0312-1 K0312-7 K0312-6 K0312-2 K0312-11 K0336-1 K0336-7 K0336-6 K0336-2 K0336-11 K0312-1 K0312-7 K0312-6 K0312-2 K0312-11 K0313-1 K0313-7 K0313-6 K0313-2 K0313-11 K0349-1 K0349-7 K0349-6 K0349-2 K0349-11 N/A N/A N/A N/A RTF
Over 200 PSI Working Pressure to 250psi to 250psi to 350psi Buna Viton Viton Carbon Carbon Carbon Ni-Resist Ni-Resist Tung Carb DXXXXX BXXXXX CXXXXX K0300-71 K0300-61 K0300-21 N/A N/A N/A K0300-71 K0300-61 K0300-21 N/A N/A N/A K0300-71 K0300-61 K0300-21 N/A N/A N/A K0414-71 K0414-61 K0414-21 K0303-71 K0303-61 K0303-21 K0416-71 K0416-61 K0416-21 K0303-71 K0303-61 K0303-21 K0303-71 K0303-61 K0303-21 K0418-71 K0418-61 K0418-21 K0303-71 K0303-61 K0303-21 K0303-71 K0303-61 K0303-21 K0303-71 K0303-61 K0303-21 K0303-71 K0303-61 K0303-21 K0306-71 K0306-61 K0306-21 K0306-71 K0306-61 K0306-21 K0307-71 K0307-61 K0307-21 K0307-71 K0307-61 K0307-21 K0308-71 K0308-61 K0308-21 K0308-71 K0308-61 K0308-21 K0309-71 K0309-61 K0309-21 K0309-71 K0309-61 K0309-21 K0334-71 K0334-61 K0334-21 K0309-71 K0309-61 K0309-21 K0334-71 K0334-61 K0334-21 K0309-71 K0309-61 K0309-21 K0458-D K0458-D K0458-C K0458-D K0458-D K0458-C K0458-D K0458-D K0458-C K0311-71 K0311-61 K0311-21 K0310-71 K0310-61 K0310-21 K0312-71 K0312-61 K0312-21 K0336-71 K0336-61 K0336-21 K0312-71 K0312-61 K0312-21 K0313-71 K0313-61 K0313-21 K0349-71 K0349-61 K0349-21 K1978 RTF RTF
Packing Kit to 500psi Buna N Carbon Ni Resist 8XXXXX N/A K0300-8 N/A K0300-8 N/A K0300-8 K0414-8 K0303-8 K0416-8 K0303-8 K0303-8 K0418-8 K0303-8 K0303-8 K0303-8 K0303-8 K0306-8 K0306-8 K0307-8 K0307-8 K0308-8 K0308-8 K0309-8 K0309-8 N/A K0309-8 N/A K0309-8 K0458-8 K0458-8 K0458-8 K0311-8 K0310-8 K0312-8 N/A K0312-8 K0313-8 N/A RTF
Packing Gland Kit
N/A K0316-1 N/A K0316-1 N/A K0316-1 K0415-1 K0319-1 K0417-1 K0319-1 K0319-1 K0419-1 K0319-1 K0319-1 K0319-1 K0319-1 K0322-1 K0322-1 K0323-1 K0323-1 K0324-1 K0324-1 K0325-1 K0325-1 K0345-1 K0325-1 K0345-1 K0325-1 K0456-1 K0456-1 K0456-1 K0327-1 K0339-1 K0328-1 K0347-1 K0328-1 K0329-1 K0348-1 K0470
N/A K0365 N/A K0365 N/A K0365 K0435 K0366 K0436 K0366 K0366 K0437 K0366 K0366 K0366 K0366 K0366 K0366 K0366 K0366 K0366 K0366 K0367 K0367 K0368 K0367 K0368 K0367 K0368 K0368 K0368 K0366 K0367 K0367 K0368 K0367 K0367 K0368 K0446
8020-3/4
X2 X3 X2 X3 X2 X3 XE X4 XF X4 X4 XG X4 X4 X4 X4 X4 X4 X4 X4 X4 X4 X5 X5 X6 X5 X6 X5 X6 X6 X6 X4 X5 X5 X6 X5 X5 X6 XK
8020-5/6
XK
N/A
N/A
N/A
N/A
K0459-A
K0459-D
K0459-B
K0459-C
K0459-8
K0460-1
K0463
1012-3/4 1012-7/8 1012-9/0 1015-1/2 1015-3/4 1020-3/4
X5 X5 X5 X7 X7 XV
K0314-1 K0314-1 K0314-1 K0315-1 K0315-1 N/A
K0314-7 K0314-7 K0314-7 K0315-7 K0315-7 N/A
K0314-6 K0314-6 K0314-6 K0315-6 K0315-6 N/A
K0314-2 K0314-2 K0314-2 K0315-2 K0315-2 N/A
K0314-11 K0314-11 K0314-11 K0315-11 K0315-11 K2381-A
K0314-71 K0314-71 K0314-71 K0315-71 K0315-71 K2381-D
K0314-61 K0314-61 K0314-61 K0315-61 K0315-61 K2381-B
K0314-21 K0314-8 K0314-21 K0314-8 K0314-21 K0314-8 K0315-21 K0315-8 K0315-21 K0315-82 K2381-C K2381-8
K0330-1 K0330-1 K0330-1 K0331-1 K0331-1 K2382
K0367 K0367 K0367 K0369 K0369 K2385
1024-1/2 1024-3/4 1216-1/2 1220-5/6 1415-1/2
XV XV
N/A N/A RTF N/A N/A
N/A N/A RTF N/A N/A
N/A N/A RTF N/A N/A
N/A N/A RTF N/A N/A
K0123-A K0123-A RTF K2319-A K0288-A
K0123-D K0123-D RTF K2319-D K0288-D
K0123-B K0123-B RTF K2319-B K0288-B
K0123-C K0123-C RTF K2319-C K0288-C
K2382-1 K2382-1 RTF RTF RTF
K2385 K2385 RTF K0463 K0463
2013-5/6 3095-7/8
3014-5/6 4095-C/D 4011-1/2 4012-1/2 4012-C/D 4011-7/8 4012-7/8 4015-5/6 4015-7/8 5012-5/6 5012-7/8 5015-7/8 5015-9/0 6012-1/2 6012-3/4 6015-1/2 6016-1/2 6019-5/6 6019-7/8 6020-3/4 6020-5/6 8012-3/4 8012-5/6 8015-1/2 8015-3/4 8018-5/6
XK XK
* For pumps with Mechanical Seals. ** For pumps with packing.
B1b.2 Page 2
K0123-8 K0123-8 RTF K2319-8 K0288-8
B1b.2 07/07 Supersedes 9/05
REPLACEMENT PARTS GUIDE SPLIT CASE PUMPS Model
Constr. Code
Gasket Hardware Bearing Kit Kit Kit
Impeller Kit (2)
Bronze
Shaft Sleeve Kit
Iron Bronze
2095-1/2
8020-3/4
X2 X3 X2 X3 X2 X3 XE X4 XF X4 X4 XG X4 X4 X4 X4 X4 X4 X4 X4 X4 X4 X5 X5 X6 X5 X6 X5 X6 X6 X6 X4 X5 X5 X6 X5 X5 X6 XK
K0360 K0360 K0360 K0360 K0360 K0360 K0360 K0361 K0433 K0361 K0361 K0434 K0361 K0361 K0361 K0361 K0385 K0385 K0362 K0362 K0386 K0386 K0363 K0363 RTF K0363 RTF K0445 K0455 K0453 K0294 K0387 K0387 K0388 RTF K0388 K0390 K0297 K0449
K0400 K0400 K0400 K0400 K0400 K0400 K0400 K0401 K0441 K0402 K0402 K0442 K0402 K0402 K0403 K0403 K0404 K0405 K0404 K0404 K0404 K0405 K0406 K0407 RTF K0408 RTF K0408 K2411 K0457 K0295 K0404 K0409 K0410 RTF K0406 K0408 K2411 K0462
K0395 K0395 K0395 K0395 K0395 K0395 K0438 K0396 K0439 K0396 K0396 K0440 K0396 K0396 K0396 K0396 K0396 K0396 K0396 K0396 K0396 K0396 K0397 K0397 K0398 K0397 K0398 K0397 K0398 K0398 K0398 K0396 K0397 K0397 K0398 K0397 K0397 K0398 K1985
K0500-B K0500-B K0501-B K0501-B K0502-B K0502-B K0426-B K0503-B K0428-B K0504-B K0504-B K0429-B K0505-B K0505-B K0506-B K0540-B K0507-B K0508-B K0509-B K0510-B K0511-B K0512-B K0513-B K0514-B K0515-B K0516-B K0517-B K0516-B K0517-B K0450-B K0296-B K0518-B K0519-B K0520-B K0521-B K0522-B K0523-B K0524-B K0444-B
8020-5/6
XK
K0461
K0462
K0465
K0444-B K0444-C
1012-3/4 1012-7/8 1012-9/0 1015-1/2 1015-3/4 1020-3/4
X5 X5 X5 X7 X7 XV
K0389 K0389 K0389 K0364 K0364 K2383
K0411 K0411 K0406 K0412 K0413 K2384
K0397 K0397 K0397 K0399 K0399 K2386
K0525-B K0525-B K0526-B K0527-B K0537-B K2387-B
K0525-C K0525-C K0526-C K0527-C K0537-C K2387-C
1024-1/2 1024-3/4 1216-1/2 1220-5/6 1415-1/2
XV XV
K0123 K0123 RTF K2373 K0371
K0278 K0278 RTF K0299 K0372
K2386 K2386 RTF K0465 K0465
K0298-B K0281-B RTF K0370-B K0373-B
K0298-C K0281-C RTF K0370-C K0373-C
2013-5/6 3095-7/8
3014-5/6 4095-C/D 4011-1/2 4012-1/2 4012-C/D 4011-7/8 4012-7/8 4015-5/6 4015-7/8 5012-5/6 5012-7/8 5015-7/8 5015-9/0 6012-1/2 6012-3/4 6015-1/2 6016-1/2 6019-5/6 6019-7/8 6020-3/4 6020-5/6 8012-3/4 8012-5/6 8015-1/2 8015-3/4 8018-5/6
XK XK
* For pumps with Mechanical Seals. ** For pumps with packing.
K0500-C K0500-C K0501-C K0501-C K0502-C K0502-C K0426-C K0503-C K0428-C K0504-C K0504-C K0429-C K0505-C K0505-C K0506-C K0540-C K0507-C K0508-C K0509-C K0510-C K0511-C K0512-C K0513-C K0514-C K0515-C K0516-C K0517-C K0516-C K0517-C K0450-C K0296-C K0518-C K0519-C K0520-C K0521-C K0522-C K0523-C K0524-C K0444-C
303 Stainless
Ceramic Coated Bronze
Hardened 416 S.S.
For Use With Balanced Seal 303 Bronze Stainless
N/A N/A N/A N/A N/A N/A K0350-0 K0350-1 K0350-5 K0350-3 K0351-00 K0351-01 N/A N/A N/A N/A N/A N/A K0350-0 K0350-1 K0350-5 K0350-3 K0351-00 K0351-01 N/A N/A N/A N/A N/A N/A K0350-0 K0350-1 K0350-5 K0350-3 K0351-00 K0351-01 K0420-0 K0420-1 K0420-5 K0420-3 K0421-00 K0421-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0422-0 K0422-1 K0422-5 K0422-3 K0423-00 K0423-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0424-0 K0424-1 K0424-5 K0424-3 K0425-00 K0425-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0529-0 K0529-1 K0529-5 K0529-3 K0529-00 K0529-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0529-0 K0529-1 K0529-5 K0529-3 K0529-00 K0529-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0529-0 K0529-1 K0529-5 K0529-3 K0529-00 K0529-01 K0533-0 K0533-1 K0533-5 K0533-3 K0533-00 K0533-01 K0354-0 K0354-1 K0354-5 K0354-3 K0355-00 K0355-01 K0357-0 K0357-1 K0357-5 K0357-3 N/A N/A K0354-0 K0354-1 K0354-5 K0354-3 K0355-00 K0355-01 K0357-0 K0357-1 K0357-5 K0357-3 N/A N/A K0433-0 K0433-1 K0433-5 K0433-3 RTF RTF K2415-0 K2415-1 K2415-5 K2415-3 RTF RTF K0451-0 K0451-1 K0451-5 K0451-3 N/A N/A K2414-0 K2414-1 K2414-5 K2414-3 RTF RTF K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0533-0 K0533-1 K0533-5 K0533-3 K0533-00 K0533-01 K0354-0 K0354-1 K0354-5 K0354-3 K0355-00 K0355-01 K0357-0 K0357-1 K0357-5 K0357-3 N/A N/A K0533-0 K0533-1 K0533-5 K0533-3 K0533-00 K0533-01 K0354-0 K0354-1 K0354-5 K0354-3 K0355-00 K0355-01 K0357-0 K0357-1 K0357-5 K0357-3 N/A N/A K0447-0* RTF RTF RTF RTF RTF K0447-09** K2321-0* K2321-1* K2321-5P** K2321-3* K0464-00 K0464-01 K2321-0P** K2321-1P** K2321-3P** K0354-0 K0354-1 K0354-5 K0354-3 K0356-00 K0356-01 K0354-0 K0354-1 K0354-5 K0354-3 K0356-00 K0356-01 K0533-0 K0533-1 K0533-5 K0533-3 K0533-00 K0533-01 K0358-0 K0358-1 K0358-5 K0358-3 K0359-00 K0359-01 K0539-0 K0539-1 K0539-5 K0539-3 K0539-00 K0539-01 K2388-0* K2388-1* K2388-5P** K2388-3* K2389-00 K2389-01 K2388-0P** K2388-1P** K2388-3P** K0279-0 K0279-1 K0279-5P** K0279-3 K0279-00 K0279-01 K0279-0 K0279-1 K0279-5P** K0279-3 K0279-00 K0279-01 RTF RTF RTF RTF RTF RTF K2395-0 K2395-1 K2395-5P K2395-3 K2395-00 K2395-01 K0391-0 K0391-1 K0391-5P K0391-3 K0391-00 K0391-01
B1b.2 Page 3
B1b.2 07/07 Supersedes 9/05
Notes:
REPLACEMENT PARTS GUIDE SPLIT CASE PUMPS Model
Constr. Code
Wear Ring Kit (1)
(1) Refer to factory for wear ring kits for double wear rings or stainless steel wear rings. (2) Available in heat-treated 17-4Ph stainless steel ONLY. Shaft Proper Ordering Number Consists of both the Shaft Number and Material Suffix Shaft Number Clockwise Packing
Seal
Packing
Steel
303 S.S.
8020-3/4
X2 X3 X2 X3 X2 X3 XE X4 XF X4 X4 XG X4 X4 X4 X4 X4 X4 X4 X4 X4 X4 X5 X5 X6 X5 X6 X5 X6 X6 X6 X4 X5 X5 X6 X5 X5 X6 XK
K0375 K0375 K0375 K0375 K0376 K0376 K0430 K0377 K0431 K0377 K0377 K0432 K0378 K0378 K0377 K0377 K0379 K0528 K0379 K0528 K0379 K0531 K0532 K0380 K0380 K0380 K0380 K0380 K0380 K0452 K0452 K0381 K0534 K0382 K0382 K0535 K0383 K0383 K0448
06007469 N/A 06007469 N/A 06007469 N/A 06018748 06007661 6019044 06007661 06007661 06018764 06007661 06007661 06007661 06007661 06007954 6018328 06007954 06018307 06007954 06018307 06018291 06016914 06017469 06016916 06017469 06034544 06034726 06019711 06034857 06007954 06018291 06016918 06017508 06018279 06016916 06017469 06019759
N/A 06007468 N/A 06007468 N/A 06007468 06018748 06007660 6019044 06007660 06007660 06018764 06007660 06007660 06007660 06007660 06007953 06018328 06007953 06018307 06007953 06018307 06018291 06016914 06017469 06016916 06017469 06034544 06034726 06019711 06034857 06007953 06018291 06016918 06017508 06018279 06016916 06017469 06019759
06007469 N/A 06007469 N/A 06007469 N/A 6019442 06007974 6019443 06007974 06007974 06019446 06007974 06007974 06007974 06007974 06007973 06018329 06007973 06018308 06007973 06018308 06018292 06016915 06017468 06016917 06017468 06034546 06034728 06019970 06034858 06007973 06018292 06016919 06017509 06018280 06016917 06017468 06019760
N/A 06007960 N/A 06007960 N/A 06007960 6019442 06007957 6019443 06007957 06007957 06019446 06007957 06007957 06007957 06007957 06007972 06018329 06007972 06018308 06007972 06018308 06018292 06016915 06017468 06016917 06017468 06034546 06034728 06019970 06034858 06007972 06018292 06016919 06017509 06018280 06016917 06017468 06019760
N/A NA N/A NA N/A N/A F F19 F F19 F19 F F19 F19 F19 F19 F19 F F19 F F19 F F F19 F19 F19 F19 F F F F F19 F F19 F19 F F19 F19 F
H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H174 (2) H174 (2) H174 (2) H174 (2) H303 H303 H303 H303 H303 H303 H303 H174 (2)
8020-5/6
XK
K0448
06040083
06040083
06040084
06040084
F
H174 (2)
1012-3/4 1012-7/8 1012-9/0 1015-1/2 1015-3/4 1020-3/4
X5 X5 X5 X7 X7 XV
K0383 K0383 K0536 K0384 K0538 K2390
06016920 06016920 06018288 06012042 06018654 06034816
06016920 06016920 06018288 06012042 06018654 06034816
06016921 06016921 06018289 06012084 06018655 06034817
06016921 06016921 06018289 06012084 06018655 06034817
F19 F19 F F F F
H303 H303 H303 H303 H303 H174 (2)
1024-1/2 1024-3/4 1216-1/2 1220-5/6 1415-1/2
XV XV
K0392 K0392 RTF K2397 K0393
06019898 06019898 RTF 06035361 06040083
06019898 06019898 RTF 06035361 06040083
06019899 06019899 RTF 06035362 06040084
06019899 06019899 RTF 06035362 06040084
F F RTF F F
H174 (2) H174 (2) RTF H174 (2) H174 (2)
2095-1/2 2013-5/6 3095-7/8
3014-5/6 4095-C/D 4011-1/2 4012-1/2 4012-C/D 4011-7/8 4012-7/8 4015-5/6 4015-7/8 5012-5/6 5012-7/8 5015-7/8 5015-9/0 6012-1/2 6012-3/4 6015-1/2 6016-1/2 6019-5/6 6019-7/8 6020-3/4 6020-5/6 8012-3/4 8012-5/6 8015-1/2 8015-3/4 8018-5/6
XK XK
Seal
plus Material Suffix
Counter Clockwise
B1b.2 Page 4
B1b.2 07/07 Supersedes 9/05
NOTES:
B1b.2 Page 5
B1b.2 07/07 Supersedes 09/05
REPLACEMENT PARTS GUIDE SPLIT CASE PUMPS EXPLANATION OF PUMP CODING (REFER TO PUMP NAMEPLATE) XX
- XXXXX
PRODUCT CODE
-
XXXXXX
MODEL NUMBER
CONSTRUCTION CODE
While PACO Split Case Pumps are designed and built to provide maximum life while requiring minimum attention and service, replacement parts may at times be required. VIRTUALLY ALL REQUIRED PARTS ARE AVAILABLE IN KIT FORM. These kits (easily selected from the charts on the preceeding pages) have been designed to insure that any part needed when replacing any split case component is furnished when you need it. KIT COMPONENTS
SEAL KIT: Mechanical Seals Gasket Kit Bearing Kit
PACKING GLAND KIT: Packing Glands Studs Nuts
PACKING KIT: Packing Set Lantern Rings Retaining Rings Gasket Kit Bearing Kit
GASKET KIT: Case Gasket Seal HSG. Gaskets Brg. Cap Gaskets Slingers
BEARING KIT: Bearings Support Washers Retaining Rings
HARDWARE KIT: Capscrews Roll Pins Nuts
WEAR RING KIT: Wear Rings Roll Pins Snap Rings
IMPELLER KIT: Bronze or Iron Impeller Impeller Key Coupling Key
SLEEVE KIT: Inboard Sleeve Outboard Sleeve Sleeve Gaskets Locking Collars (where applicable)
NOTE:
SHAFTS: Steel or Stainless Packed or Seal
Kits may not contain all parts listed. They are individually selected for each pump. Some parts may not be appropriate depending on the design of the specific model or pump size. WWW.PACOPUMPS.COM
B1b.2 Page 6
PACO PUMPS
SPLIT CASE PUMPS REPLACEMENT PARTS GUIDE TYPES KP & KPV
®
CAT#: STOCK#:
WWW.PACOPUMPS.COM
SER#: IMP
GPM:
DIA: TDH: BROOKSHIRE, TEXAS
'
PACO Split Case Kits are arranged so that you can replace virtually any component with minimum of effort. Here are some guidelines and suggestions: GENERAL NOTES: The pump nameplate contains all data required for the selection and ordering of the proper replacement parts kit. The PUMP MODEL and SERIAL NUMBER should be referenced whenever any replacement parts kit is ordered, while the PUMP CONDITIONS (GPM & TDH) and IMPELLER TRIM (IMP DIA) are REQUIRED data for the ordering of replacement impellers. To replace a mechanical seal. Select the correct Seal Kit which will maximize seal life and eliminate future down time. Shaft sleeve inspection is suggested, and replacement made as indicated. (Note that a PACO Seal kit will already contain a complete Gasket Kit and Bearing Kit)
To replace impeller. An Impeller Kit is required; a Wear Ring Kit is highly recommended, and a Seal or Packing Kit will provide all other normally replaced components.
To replace the packing A packing kit is needed. Shaft sleeve inspection is recommended. If packing glands are damaged, they may be replaced by ordering the proper Packing Gland kit. (Note that PACO Packing Kits will already contain a complete Gasket Kit and Bearing Kit).
To replace the shaft. The correct shaft should be selected. Shaft replacement is most often accompanied by replacement of the seal or packing and sleeves.
To replace the shaft sleeves. You will need a Shaft sleeve Kit. A Seal or Packing Kit will provide other normally needed parts.
To inspect the pump internals. Since gaskets are often damaged, a Gasket Kit is recommended.
To replace bearings. A Bearing Kit is required and a Gasket Kt is recommended. Bearing Kits and Gasket Kits are included in Seal/Packing Kits.
To overhaul the pump. (Replace Rotating Assembly). You will need an Impeller Kit, a Wear Ring Kit, a Shaft Sleeve Kit, a Seal or Packing Kit, and a shaft.
To replace wear rings. A Wear Ring kit is required. A Seal/Packing Kit will provide all other normally replaced components.
To replace lost or damaged hardware. Hardware Kits are available for 175 PSI units. (For 250 PSI refer to factory).
NOTE: Seal/Packing Kits are always recommended as spare parts
B1b.2 Page 1
B1b.2 07/07 Supersedes 9/05
REPLACEMENT PARTS GUIDE SPLIT CASE PUMPS Model
2095-1/2
Constr. Code
Mechanical Seal Kit To 200 PSI Working Pressure to 212psi Buna N Buna N Viton Viton Buna N Carbon Carbon Carbon Carbon Carbon Ceramic Ni Resist Ni Resist Tung Crbd Ceramic 1XXXXX 7XXXXX 6XXXXX 2XXXXX AXXXXX K0300-1 K0300-7 K0300-6 K0300-2 K0300-11 N/A N/A N/A N/A N/A K0300-1 K0300-7 K0300-6 K0300-2 K0300-11 N/A N/A N/A N/A N/A K0300-1 K0300-7 K0300-6 K0300-2 K0300-11 N/A N/A N/A N/A N/A K0414-1 K0414-7 K0414-6 K0414-2 K0414-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0416-1 K0416-7 K0416-6 K0416-2 K0416-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0418-1 K0418-7 K0418-6 K0418-2 K0418-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0303-1 K0303-7 K0303-6 K0303-2 K0303-11 K0306-1 K0306-7 K0306-6 K0306-2 K0306-11 K0306-1 K0306-7 K0306-6 K0306-2 K0306-11 K0307-1 K0307-7 K0307-6 K0307-2 K0307-11 K0307-1 K0307-7 K0307-6 K0307-2 K0307-11 K0308-1 K0308-7 K0308-6 K0308-2 K0308-11 K0308-1 K0308-7 K0308-6 K0308-2 K0308-11 K0309-1 K0309-7 K0309-6 K0309-2 K0309-11 K0309-1 K0309-7 K0309-6 K0309-2 K0309-11 K0334-1 K0334-7 K0334-6 K0334-2 K0334-11 K0309-1 K0309-7 K0309-6 K0309-2 K0309-11 K0334-1 K0334-7 K0334-6 K0334-2 K0334-11 K0309-1 K0309-7 K0309-6 K0309-2 K0309-11 K0458-1 K0458-7 K0458-6 K0458-2 K0458-A K0458-1 K0458-7 K0458-6 K0458-2 K0458-A K0458-1 K0458-7 K0458-6 K0458-2 K0458-A K0311-1 K0311-7 K0311-6 K0311-2 K0311-11 K0310-1 K0310-7 K0310-6 K0310-2 K0310-11 K0312-1 K0312-7 K0312-6 K0312-2 K0312-11 K0336-1 K0336-7 K0336-6 K0336-2 K0336-11 K0312-1 K0312-7 K0312-6 K0312-2 K0312-11 K0313-1 K0313-7 K0313-6 K0313-2 K0313-11 K0349-1 K0349-7 K0349-6 K0349-2 K0349-11 N/A N/A N/A N/A RTF
Over 200 PSI Working Pressure to 250psi to 250psi to 350psi Buna Viton Viton Carbon Carbon Carbon Ni-Resist Ni-Resist Tung Carb DXXXXX BXXXXX CXXXXX K0300-71 K0300-61 K0300-21 N/A N/A N/A K0300-71 K0300-61 K0300-21 N/A N/A N/A K0300-71 K0300-61 K0300-21 N/A N/A N/A K0414-71 K0414-61 K0414-21 K0303-71 K0303-61 K0303-21 K0416-71 K0416-61 K0416-21 K0303-71 K0303-61 K0303-21 K0303-71 K0303-61 K0303-21 K0418-71 K0418-61 K0418-21 K0303-71 K0303-61 K0303-21 K0303-71 K0303-61 K0303-21 K0303-71 K0303-61 K0303-21 K0303-71 K0303-61 K0303-21 K0306-71 K0306-61 K0306-21 K0306-71 K0306-61 K0306-21 K0307-71 K0307-61 K0307-21 K0307-71 K0307-61 K0307-21 K0308-71 K0308-61 K0308-21 K0308-71 K0308-61 K0308-21 K0309-71 K0309-61 K0309-21 K0309-71 K0309-61 K0309-21 K0334-71 K0334-61 K0334-21 K0309-71 K0309-61 K0309-21 K0334-71 K0334-61 K0334-21 K0309-71 K0309-61 K0309-21 K0458-D K0458-D K0458-C K0458-D K0458-D K0458-C K0458-D K0458-D K0458-C K0311-71 K0311-61 K0311-21 K0310-71 K0310-61 K0310-21 K0312-71 K0312-61 K0312-21 K0336-71 K0336-61 K0336-21 K0312-71 K0312-61 K0312-21 K0313-71 K0313-61 K0313-21 K0349-71 K0349-61 K0349-21 K1978 RTF RTF
Packing Kit to 500psi Buna N Carbon Ni Resist 8XXXXX N/A K0300-8 N/A K0300-8 N/A K0300-8 K0414-8 K0303-8 K0416-8 K0303-8 K0303-8 K0418-8 K0303-8 K0303-8 K0303-8 K0303-8 K0306-8 K0306-8 K0307-8 K0307-8 K0308-8 K0308-8 K0309-8 K0309-8 N/A K0309-8 N/A K0309-8 K0458-8 K0458-8 K0458-8 K0311-8 K0310-8 K0312-8 N/A K0312-8 K0313-8 N/A RTF
Packing Gland Kit
N/A K0316-1 N/A K0316-1 N/A K0316-1 K0415-1 K0319-1 K0417-1 K0319-1 K0319-1 K0419-1 K0319-1 K0319-1 K0319-1 K0319-1 K0322-1 K0322-1 K0323-1 K0323-1 K0324-1 K0324-1 K0325-1 K0325-1 K0345-1 K0325-1 K0345-1 K0325-1 K0456-1 K0456-1 K0456-1 K0327-1 K0339-1 K0328-1 K0347-1 K0328-1 K0329-1 K0348-1 K0470
N/A K0365 N/A K0365 N/A K0365 K0435 K0366 K0436 K0366 K0366 K0437 K0366 K0366 K0366 K0366 K0366 K0366 K0366 K0366 K0366 K0366 K0367 K0367 K0368 K0367 K0368 K0367 K0368 K0368 K0368 K0366 K0367 K0367 K0368 K0367 K0367 K0368 K0446
8020-3/4
X2 X3 X2 X3 X2 X3 XE X4 XF X4 X4 XG X4 X4 X4 X4 X4 X4 X4 X4 X4 X4 X5 X5 X6 X5 X6 X5 X6 X6 X6 X4 X5 X5 X6 X5 X5 X6 XK
8020-5/6
XK
N/A
N/A
N/A
N/A
K0459-A
K0459-D
K0459-B
K0459-C
K0459-8
K0460-1
K0463
1012-3/4 1012-7/8 1012-9/0 1015-1/2 1015-3/4 1020-3/4
X5 X5 X5 X7 X7 XV
K0314-1 K0314-1 K0314-1 K0315-1 K0315-1 N/A
K0314-7 K0314-7 K0314-7 K0315-7 K0315-7 N/A
K0314-6 K0314-6 K0314-6 K0315-6 K0315-6 N/A
K0314-2 K0314-2 K0314-2 K0315-2 K0315-2 N/A
K0314-11 K0314-11 K0314-11 K0315-11 K0315-11 K2381-A
K0314-71 K0314-71 K0314-71 K0315-71 K0315-71 K2381-D
K0314-61 K0314-61 K0314-61 K0315-61 K0315-61 K2381-B
K0314-21 K0314-8 K0314-21 K0314-8 K0314-21 K0314-8 K0315-21 K0315-8 K0315-21 K0315-82 K2381-C K2381-8
K0330-1 K0330-1 K0330-1 K0331-1 K0331-1 K2382
K0367 K0367 K0367 K0369 K0369 K2385
1024-1/2 1024-3/4 1216-1/2 1220-5/6 1415-1/2
XV XV
N/A N/A RTF N/A N/A
N/A N/A RTF N/A N/A
N/A N/A RTF N/A N/A
N/A N/A RTF N/A N/A
K0123-A K0123-A RTF K2319-A K0288-A
K0123-D K0123-D RTF K2319-D K0288-D
K0123-B K0123-B RTF K2319-B K0288-B
K0123-C K0123-C RTF K2319-C K0288-C
K2382-1 K2382-1 RTF RTF RTF
K2385 K2385 RTF K0463 K0463
2013-5/6 3095-7/8
3014-5/6 4095-C/D 4011-1/2 4012-1/2 4012-C/D 4011-7/8 4012-7/8 4015-5/6 4015-7/8 5012-5/6 5012-7/8 5015-7/8 5015-9/0 6012-1/2 6012-3/4 6015-1/2 6016-1/2 6019-5/6 6019-7/8 6020-3/4 6020-5/6 8012-3/4 8012-5/6 8015-1/2 8015-3/4 8018-5/6
XK XK
* For pumps with Mechanical Seals. ** For pumps with packing.
B1b.2 Page 2
K0123-8 K0123-8 RTF K2319-8 K0288-8
B1b.2 07/07 Supersedes 9/05
REPLACEMENT PARTS GUIDE SPLIT CASE PUMPS Model
Constr. Code
Gasket Hardware Bearing Kit Kit Kit
Impeller Kit (2)
Bronze
Shaft Sleeve Kit
Iron Bronze
2095-1/2
8020-3/4
X2 X3 X2 X3 X2 X3 XE X4 XF X4 X4 XG X4 X4 X4 X4 X4 X4 X4 X4 X4 X4 X5 X5 X6 X5 X6 X5 X6 X6 X6 X4 X5 X5 X6 X5 X5 X6 XK
K0360 K0360 K0360 K0360 K0360 K0360 K0360 K0361 K0433 K0361 K0361 K0434 K0361 K0361 K0361 K0361 K0385 K0385 K0362 K0362 K0386 K0386 K0363 K0363 RTF K0363 RTF K0445 K0455 K0453 K0294 K0387 K0387 K0388 RTF K0388 K0390 K0297 K0449
K0400 K0400 K0400 K0400 K0400 K0400 K0400 K0401 K0441 K0402 K0402 K0442 K0402 K0402 K0403 K0403 K0404 K0405 K0404 K0404 K0404 K0405 K0406 K0407 RTF K0408 RTF K0408 K2411 K0457 K0295 K0404 K0409 K0410 RTF K0406 K0408 K2411 K0462
K0395 K0395 K0395 K0395 K0395 K0395 K0438 K0396 K0439 K0396 K0396 K0440 K0396 K0396 K0396 K0396 K0396 K0396 K0396 K0396 K0396 K0396 K0397 K0397 K0398 K0397 K0398 K0397 K0398 K0398 K0398 K0396 K0397 K0397 K0398 K0397 K0397 K0398 K1985
K0500-B K0500-B K0501-B K0501-B K0502-B K0502-B K0426-B K0503-B K0428-B K0504-B K0504-B K0429-B K0505-B K0505-B K0506-B K0540-B K0507-B K0508-B K0509-B K0510-B K0511-B K0512-B K0513-B K0514-B K0515-B K0516-B K0517-B K0516-B K0517-B K0450-B K0296-B K0518-B K0519-B K0520-B K0521-B K0522-B K0523-B K0524-B K0444-B
8020-5/6
XK
K0461
K0462
K0465
K0444-B K0444-C
1012-3/4 1012-7/8 1012-9/0 1015-1/2 1015-3/4 1020-3/4
X5 X5 X5 X7 X7 XV
K0389 K0389 K0389 K0364 K0364 K2383
K0411 K0411 K0406 K0412 K0413 K2384
K0397 K0397 K0397 K0399 K0399 K2386
K0525-B K0525-B K0526-B K0527-B K0537-B K2387-B
K0525-C K0525-C K0526-C K0527-C K0537-C K2387-C
1024-1/2 1024-3/4 1216-1/2 1220-5/6 1415-1/2
XV XV
K0123 K0123 RTF K2373 K0371
K0278 K0278 RTF K0299 K0372
K2386 K2386 RTF K0465 K0465
K0298-B K0281-B RTF K0370-B K0373-B
K0298-C K0281-C RTF K0370-C K0373-C
2013-5/6 3095-7/8
3014-5/6 4095-C/D 4011-1/2 4012-1/2 4012-C/D 4011-7/8 4012-7/8 4015-5/6 4015-7/8 5012-5/6 5012-7/8 5015-7/8 5015-9/0 6012-1/2 6012-3/4 6015-1/2 6016-1/2 6019-5/6 6019-7/8 6020-3/4 6020-5/6 8012-3/4 8012-5/6 8015-1/2 8015-3/4 8018-5/6
XK XK
* For pumps with Mechanical Seals. ** For pumps with packing.
K0500-C K0500-C K0501-C K0501-C K0502-C K0502-C K0426-C K0503-C K0428-C K0504-C K0504-C K0429-C K0505-C K0505-C K0506-C K0540-C K0507-C K0508-C K0509-C K0510-C K0511-C K0512-C K0513-C K0514-C K0515-C K0516-C K0517-C K0516-C K0517-C K0450-C K0296-C K0518-C K0519-C K0520-C K0521-C K0522-C K0523-C K0524-C K0444-C
303 Stainless
Ceramic Coated Bronze
Hardened 416 S.S.
For Use With Balanced Seal 303 Bronze Stainless
N/A N/A N/A N/A N/A N/A K0350-0 K0350-1 K0350-5 K0350-3 K0351-00 K0351-01 N/A N/A N/A N/A N/A N/A K0350-0 K0350-1 K0350-5 K0350-3 K0351-00 K0351-01 N/A N/A N/A N/A N/A N/A K0350-0 K0350-1 K0350-5 K0350-3 K0351-00 K0351-01 K0420-0 K0420-1 K0420-5 K0420-3 K0421-00 K0421-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0422-0 K0422-1 K0422-5 K0422-3 K0423-00 K0423-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0424-0 K0424-1 K0424-5 K0424-3 K0425-00 K0425-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0529-0 K0529-1 K0529-5 K0529-3 K0529-00 K0529-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0529-0 K0529-1 K0529-5 K0529-3 K0529-00 K0529-01 K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0529-0 K0529-1 K0529-5 K0529-3 K0529-00 K0529-01 K0533-0 K0533-1 K0533-5 K0533-3 K0533-00 K0533-01 K0354-0 K0354-1 K0354-5 K0354-3 K0355-00 K0355-01 K0357-0 K0357-1 K0357-5 K0357-3 N/A N/A K0354-0 K0354-1 K0354-5 K0354-3 K0355-00 K0355-01 K0357-0 K0357-1 K0357-5 K0357-3 N/A N/A K0433-0 K0433-1 K0433-5 K0433-3 RTF RTF K2415-0 K2415-1 K2415-5 K2415-3 RTF RTF K0451-0 K0451-1 K0451-5 K0451-3 N/A N/A K2414-0 K2414-1 K2414-5 K2414-3 RTF RTF K0352-0 K0352-1 K0352-5 K0352-3 K0353-00 K0353-01 K0533-0 K0533-1 K0533-5 K0533-3 K0533-00 K0533-01 K0354-0 K0354-1 K0354-5 K0354-3 K0355-00 K0355-01 K0357-0 K0357-1 K0357-5 K0357-3 N/A N/A K0533-0 K0533-1 K0533-5 K0533-3 K0533-00 K0533-01 K0354-0 K0354-1 K0354-5 K0354-3 K0355-00 K0355-01 K0357-0 K0357-1 K0357-5 K0357-3 N/A N/A K0447-0* RTF RTF RTF RTF RTF K0447-09** K2321-0* K2321-1* K2321-5P** K2321-3* K0464-00 K0464-01 K2321-0P** K2321-1P** K2321-3P** K0354-0 K0354-1 K0354-5 K0354-3 K0356-00 K0356-01 K0354-0 K0354-1 K0354-5 K0354-3 K0356-00 K0356-01 K0533-0 K0533-1 K0533-5 K0533-3 K0533-00 K0533-01 K0358-0 K0358-1 K0358-5 K0358-3 K0359-00 K0359-01 K0539-0 K0539-1 K0539-5 K0539-3 K0539-00 K0539-01 K2388-0* K2388-1* K2388-5P** K2388-3* K2389-00 K2389-01 K2388-0P** K2388-1P** K2388-3P** K0279-0 K0279-1 K0279-5P** K0279-3 K0279-00 K0279-01 K0279-0 K0279-1 K0279-5P** K0279-3 K0279-00 K0279-01 RTF RTF RTF RTF RTF RTF K2395-0 K2395-1 K2395-5P K2395-3 K2395-00 K2395-01 K0391-0 K0391-1 K0391-5P K0391-3 K0391-00 K0391-01
B1b.2 Page 3
B1b.2 07/07 Supersedes 9/05
Notes:
REPLACEMENT PARTS GUIDE SPLIT CASE PUMPS Model
Constr. Code
Wear Ring Kit (1)
(1) Refer to factory for wear ring kits for double wear rings or stainless steel wear rings. (2) Available in heat-treated 17-4Ph stainless steel ONLY. Shaft Proper Ordering Number Consists of both the Shaft Number and Material Suffix Shaft Number Clockwise Packing
Seal
Packing
Steel
303 S.S.
8020-3/4
X2 X3 X2 X3 X2 X3 XE X4 XF X4 X4 XG X4 X4 X4 X4 X4 X4 X4 X4 X4 X4 X5 X5 X6 X5 X6 X5 X6 X6 X6 X4 X5 X5 X6 X5 X5 X6 XK
K0375 K0375 K0375 K0375 K0376 K0376 K0430 K0377 K0431 K0377 K0377 K0432 K0378 K0378 K0377 K0377 K0379 K0528 K0379 K0528 K0379 K0531 K0532 K0380 K0380 K0380 K0380 K0380 K0380 K0452 K0452 K0381 K0534 K0382 K0382 K0535 K0383 K0383 K0448
06007469 N/A 06007469 N/A 06007469 N/A 06018748 06007661 6019044 06007661 06007661 06018764 06007661 06007661 06007661 06007661 06007954 6018328 06007954 06018307 06007954 06018307 06018291 06016914 06017469 06016916 06017469 06034544 06034726 06019711 06034857 06007954 06018291 06016918 06017508 06018279 06016916 06017469 06019759
N/A 06007468 N/A 06007468 N/A 06007468 06018748 06007660 6019044 06007660 06007660 06018764 06007660 06007660 06007660 06007660 06007953 06018328 06007953 06018307 06007953 06018307 06018291 06016914 06017469 06016916 06017469 06034544 06034726 06019711 06034857 06007953 06018291 06016918 06017508 06018279 06016916 06017469 06019759
06007469 N/A 06007469 N/A 06007469 N/A 6019442 06007974 6019443 06007974 06007974 06019446 06007974 06007974 06007974 06007974 06007973 06018329 06007973 06018308 06007973 06018308 06018292 06016915 06017468 06016917 06017468 06034546 06034728 06019970 06034858 06007973 06018292 06016919 06017509 06018280 06016917 06017468 06019760
N/A 06007960 N/A 06007960 N/A 06007960 6019442 06007957 6019443 06007957 06007957 06019446 06007957 06007957 06007957 06007957 06007972 06018329 06007972 06018308 06007972 06018308 06018292 06016915 06017468 06016917 06017468 06034546 06034728 06019970 06034858 06007972 06018292 06016919 06017509 06018280 06016917 06017468 06019760
N/A NA N/A NA N/A N/A F F19 F F19 F19 F F19 F19 F19 F19 F19 F F19 F F19 F F F19 F19 F19 F19 F F F F F19 F F19 F19 F F19 F19 F
H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H303 H174 (2) H174 (2) H174 (2) H174 (2) H303 H303 H303 H303 H303 H303 H303 H174 (2)
8020-5/6
XK
K0448
06040083
06040083
06040084
06040084
F
H174 (2)
1012-3/4 1012-7/8 1012-9/0 1015-1/2 1015-3/4 1020-3/4
X5 X5 X5 X7 X7 XV
K0383 K0383 K0536 K0384 K0538 K2390
06016920 06016920 06018288 06012042 06018654 06034816
06016920 06016920 06018288 06012042 06018654 06034816
06016921 06016921 06018289 06012084 06018655 06034817
06016921 06016921 06018289 06012084 06018655 06034817
F19 F19 F F F F
H303 H303 H303 H303 H303 H174 (2)
1024-1/2 1024-3/4 1216-1/2 1220-5/6 1415-1/2
XV XV
K0392 K0392 RTF K2397 K0393
06019898 06019898 RTF 06035361 06040083
06019898 06019898 RTF 06035361 06040083
06019899 06019899 RTF 06035362 06040084
06019899 06019899 RTF 06035362 06040084
F F RTF F F
H174 (2) H174 (2) RTF H174 (2) H174 (2)
2095-1/2 2013-5/6 3095-7/8
3014-5/6 4095-C/D 4011-1/2 4012-1/2 4012-C/D 4011-7/8 4012-7/8 4015-5/6 4015-7/8 5012-5/6 5012-7/8 5015-7/8 5015-9/0 6012-1/2 6012-3/4 6015-1/2 6016-1/2 6019-5/6 6019-7/8 6020-3/4 6020-5/6 8012-3/4 8012-5/6 8015-1/2 8015-3/4 8018-5/6
XK XK
Seal
plus Material Suffix
Counter Clockwise
B1b.2 Page 4
B1b.2 07/07 Supersedes 9/05
NOTES:
B1b.2 Page 5
B1b.2 07/07 Supersedes 09/05
REPLACEMENT PARTS GUIDE SPLIT CASE PUMPS EXPLANATION OF PUMP CODING (REFER TO PUMP NAMEPLATE) XX
- XXXXX
PRODUCT CODE
-
XXXXXX
MODEL NUMBER
CONSTRUCTION CODE
While PACO Split Case Pumps are designed and built to provide maximum life while requiring minimum attention and service, replacement parts may at times be required. VIRTUALLY ALL REQUIRED PARTS ARE AVAILABLE IN KIT FORM. These kits (easily selected from the charts on the preceeding pages) have been designed to insure that any part needed when replacing any split case component is furnished when you need it. KIT COMPONENTS
SEAL KIT: Mechanical Seals Gasket Kit Bearing Kit
PACKING GLAND KIT: Packing Glands Studs Nuts
PACKING KIT: Packing Set Lantern Rings Retaining Rings Gasket Kit Bearing Kit
GASKET KIT: Case Gasket Seal HSG. Gaskets Brg. Cap Gaskets Slingers
BEARING KIT: Bearings Support Washers Retaining Rings
HARDWARE KIT: Capscrews Roll Pins Nuts
WEAR RING KIT: Wear Rings Roll Pins Snap Rings
IMPELLER KIT: Bronze or Iron Impeller Impeller Key Coupling Key
SLEEVE KIT: Inboard Sleeve Outboard Sleeve Sleeve Gaskets Locking Collars (where applicable)
NOTE:
SHAFTS: Steel or Stainless Packed or Seal
Kits may not contain all parts listed. They are individually selected for each pump. Some parts may not be appropriate depending on the design of the specific model or pump size. WWW.PACOPUMPS.COM
B1b.2 Page 6
Free Serial Numbers
Fhp Heat Pump Serial Numbers
- PUMP MANUFACTURERS’ CROSS-REFERENCE U.S. Seal Mating Mating Material Part No. Size Head Ring Ring Bore Code Notes Pump Nameplate Data Mfg. ABS USA PS-851 3/4 A 1 1.375 BCFJF 11107939 PS-446 1-3/4 C 1 2.500 BCFJF 11116013 PS-267 2 C 1 2.750 BCFJF 11116014.
- PUMP IDENTIFICATION • All PACO Pumps are identified by Catalog and Serial Numbers. These numbers are stamped on the pump nameplate (Fig.1 a) affixed to each pump volute casing, and should be referred to in all correspondence with the Company. PACO PUMPS B. RECEIVING • Check pumping unit for shortage and damage immediately upon arrival.
Software Serial Numbers
Paco Pump Repair Parts
Browse product catalogue. Browse by product family, pump design or application area. Guided selection. Find a suitable pump based on head, flow and design. Joyoung soy milk. Driver home stepper unipolar. Replace an existing product. Find a Grundfos pump to replace old Grundfos and competitor products. Find a product by liquid. Document Number Literature language Literature category. https://skieyharmony201.weebly.com/american-horizons-schaller-pdf-download.html.